Moncks Corner Dating

※ Download: Spoolmatic 30a hookup

Controls Trigger Press trigger to energize welding power source contactor if applica- ble , start shielding gas flow, and begin wire feed. Set the voltage switch to panel not remote and the contactor switch to remote. Arc rays from the welding process produce intense visible and invisible ultraviolet and infrared rays D Always ventilate confined spaces or use that can burn eyes and skin.

Determine which spool gun works with each... I went back out and noticed the pc300 had gtaw on it, so I got my memory refreshed there and here. This group of symbols means Warning! Its been a while since I've messed with this power supply and to be quite honest, my memory and ability to dope this type of stuff out isnt worth a hoot anymore.

Miller Spoolmatic 30A #130831 - Replacing Contact Tip Adapter Barrel Extension Remove as shown.

The thought of tig'n all this stuff is just killing me. The spool gun has no type 1 or 2 on it, its just an older pop top not hinged 30 amp gun without a serial number. Its been sitting since he gave it to me and now I have a decent job for it. Do I have what I need to make this rig run? Any other equioment needed for good results? Any pointers on hookup and use? Its been a while since I've messed with this power supply and to be quite honest, my memory and ability to dope this type of stuff out isnt worth a hoot anymore. If I could get the answers here it would probably save me half a day of reading and fooling around, messing something up and costing me more time and money. I just hate spending it on my stupidity. The wire speed is on the bottom of the gun, I assume the spool gun has pre and post flow points on the trigger that controls the gas? Guess there is no way to use the pedal for power here, since the wc plugs into the multi pin connector. Stuck with the knob 15 feet from the work?... This would be a dc+ process with straight argon? I have the same setup, the wc24 hooks to the 14pin amphenol plug, the spoolgun to the 10 pin plug, gas hose to straight argon flowmeter, and the weld lead to the cv red lug. Set the voltage switch to panel not remote and the contactor switch to remote. The trigger on the spoolgun is two stage, pull the trigger halfway and you get gasflow, pull it all the way and you get wire. Mabey somebody else can tell you what the psa2 is for, as far as I know you do not need it with waht you have. Thanks Chad, Yep its a spoolmatic 30a gun, wouldnt happen to know where ther serial number is on that thing would you? I would like to get some docs on it and get familiar with it. I'm not sure the pinout connections in the 14 and 9 are right, I have no idea what this thing was connected to before it wound up in my hands. Need to track that down before any power hits it. Funny thing, the 14 pin that connects to the source only has 3 pins in it. Guess thats all thats needed for the spool motor in the gun. Wonder if I should disconnect the tig gear before turning it on with the spoolgun coonnected? Nice to find a roll of 4043. Any trick suggestions or issues with this setup? Thanks again, I'll fiddle with it this evening and see if I can get it running. W means water cooled and 15 means 15 foot gun lead. I have a 15A here. I went back out and noticed the pc300 had gtaw on it, so I got my memory refreshed there and here. Did a little tig'n just to see how shakey I am after not touching it for a few months and before I hook the spool gun up and the beads were very dull, probably bad gas as I've had problems with this gas supplier before. Add to that, after a few beads, I noticed the gas kept flowing well after I was off the pedal, like forever. Pulled the pedal and tried it, still flowing, pulled the line off the gas valve and tried it, still flowing from the valve. Turn the hf on and off and I can feel the selinoid clicking but the gas still flows from the valve no matter what I do or what switch I throw. Looks like I need to pull the cover and do the checks on this thing to see whats going on. I'll post this in a new thread too. I wonder if that old gas messed it up.

Welding Aluminum TIG vs MIG Spool Gun
The 251 has a spool gun plug that only works with a 30a or30 w type spool gun. Replacing Canister Inlet Guide Top Cover Pressure Roll Assembly Cut off welding wire where it enters pressure roll assembly area. Routine Maintenance Y Disconnect power Maintain more often before maintaining. You will need matching plugs If they have the sockets all ready installed. I just hate spending it on my stupidity. Tried the new liner in the torch, the new tip and clamping the wire feed assembly with a clamp instead of the tensioner. If I could get the answers here it would probably save me half a day of reading and fooling around, messing something up and costing me more time and money. This would be a dc+ process with straight argon? I would like to get some docs on it and get familiar with it. If tab is removed, a smaller di- ameter contact tip is recom- mended.